Transfer Pumps

Sort By:  
34535XL.jpg
Rule - Rule iL500 Plus Inline Pump Kit - 12V (34535)
iL500 Plus Pump Kit 12v

Flow rate to 7 USgallons/min
Pressure up to 14 psi

Features:
  • Suitable for diesel, fresh and salt water
  • Quick diesel transfer with no spillage
  • Water transfer, deck shower, or deck wash
  • Continuous rating but should not be run dry for long periods
  • Includes Spray Nozzle, 4m cable with battery clips, 4m layflat hose.

WarningWARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

$80.82
34572XL.jpg
Jabsco - Jabsco Light Duty Vane Transfer Pump - 12v (34572)
Light Duty Vane Pump
Diesel Transfer Pump

Flow rate: 6 USgallons/min
Self-priming from dry up to 3ft

The Jabsco Reversible Rotary Vane Pump is ideal for transferring diesel fuel. It is self-priming to about three feet and can pump against a discharge head up to twenty feet.
Features:
  • The pump head may be mounted at 90°
  • increments on the motor to allow mounting as needed
  • Meets USCG 183.410 & ISO8846 Marine (Ignition Protection)


Motor
Intermittant duty permanent magnet type

Port Type
1/2" NPT Female or 1" (25mm) Hose barb

WarningWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

$326.88
34573XL.jpg
Jabsco - Jabsco Light Duty Reversible Diesel Transfer Pump (34573)
Reversible Vane Pump
Diesel Transfer Pump

Flow rate: 7.9 USgallons/min)
Self-priming from dry up to 3ft

The Jabsco Reversible Rotary Vane Pump is ideal for transferring diesel fuel. It is self-priming to about three feet and can pump against a discharge head up to twenty feet. With its integral on-off reversing switch, it is ideal for moving fuel between port and starboard fuel tanks.

Features:
  • The pump head may be mounted at 90°
  • increments on the motor to allow mounting as needed
  • Meets USCG 183.410 & ISO8846 Marine (Ignition Protection)


Motor
Intermittant duty permanent magnet type with reversing switch

Port Type
1/2" NPT Female or 1" (25mm) Hose barb

WarningWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

$331.61
46334XL.jpg
Beckson Marine - Beckson Handy-Mate Utility Pump - 16" (46334)
Handy-Mate Utility Pump

Beckson's Handy-Mate pumps can be used around the home, car, RV or anywhere to handle routine and emergency pumping jobs. They are designed to handle all the routine pumping jobs, plus the unusual ones. They can pump water out of bilges, sump tanks and from one tank to another, or pump oil from inboard or stern drive or engine crankcases when it needs changing. A tube is provided to insert into the dipstick hole and the oil is quickly pumped out. The especially versatile 216PC pumps come with a kit of tubes, hoses, reducing foot and adapter. The Handy Mate is made entirely of tough marine plastic. It will not rust or corrode, is non-sparking for safety, and requires no priming to start pumping action. The pump body has a diameter of 1-1/2" (38mm), and it is fitted with a comfortable molded handle for easy, no-strain operation.

Features:
  • Length: 16" (40.6cm)
  • Diameter: 1-1/2" (38mm)
  • Pumps: 10 oz./stroke
  • Two intake tubes:
    • 36" (91.4cm) long x 1/2' (13mm)
    • 1/4" (7mm) x 36" (91.4cm) w/adptr

  • Flexible hose for water discharge:
    • 1-1/4" (45mm) x 24" (61cm)

  • Red discharge tube for oil:
      1-1/4" (45mm) x 10" (25mm)

WarningWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

$33.78
56114XL.jpg
SHURFLO - SHURFLO PIRANHA™ Ballast 800 Pump - 12 VDC, 800 GPH (56114)
PIRANHA™ Ballast 800 Pump - 12 VDC, 800 GPH

Everything you are looking for in a ballast pump. Our tough, high density nylon housing and heavy duty water cooled motor give the PIRANHA ballast pumps unparalleled reliability. Anti airlock feature allows the pump to clear trapped air. All ballast series pumps have a removable cartridge for easy cleaning and ease of replacement.

Features:
  • Flow Rate 800 GPH
  • Replaceable Cartridge
  • Tough Nylon Construction
  • Anti-Air Lock Feature
  • Tinned 6 Feet Wire Assembly
  • CE, Ignition Protected ISO 8846
$37.50
56115XL.jpg
SHURFLO - SHURFLO PIRANHA™ Ballast 1100 Pump - 12 VDC, 1100 GPH (56115)
PIRANHA™ Ballast 1100 Pump - 12 VDC, 1100 GPH

Everything you are looking for in a ballast pump. Our tough, high density nylon housing and heavy duty water cooled motor give the PIRANHA ballast pumps unparalleled reliability. Anti airlock feature allows the pump to clear trapped air. All ballast series pumps have a removable cartridge for easy cleaning and ease of replacement.

Features:
  • Flow Rate 1100 GPH
  • Replaceable Cartridge
  • Tough Nylon Construction
  • Anti-Air Lock Feature
  • Tinned 6 Feet Wire Assembly
  • CE, Ignition Protected ISO 8846
$40.78
56130XL.jpg
SHURFLO - SHURFLO Standard Utility Pump - 12 VDC, 1.5 GPM (56130)
Standard Utility Pump - 12 VDC, 1.5 GPM

Incorporating SHURFLO's advanced motor technology that includes thermal overload protection, the general purpose pumps are self-priming, easy to install and are extremely versatile.

Features:
  • 12 VDC
  • Ignition Protected
  • BUNA Valves
  • CE
  • 7' [2.1m] Prime
  • Hose kit Included
  • Uses: Winterizing, Oil Change and Liquid Transfers
$122.21
56131XL.jpg
SHURFLO - SHURFLO Premium Utility Pump - 12 VDC, 1.5 GPM (56131)
Premium Utility Pump - 12 VDC, 1.5 GPM

Incorporating SHURFLO's advanced motor technology that includes thermal overload protection, general utility pumps are self-priming, easy to install and are extremely versatile-perfect for a variety of uses including winterizing, oil changing and liquid transfer. 1 Year Warranty.

Features:
  • 12 VDC
  • Ignition Protected
  • BUNA Valves
  • CE
  • 7' [2.1m] Prime
  • 8' Cable with Battery Clips
  • Hose kit Included
  • Uses: Winterizing, Oil Change and Liquid Transfers
$141.99
60299XL.jpg
Johnson Pump - Johnson Pump Ultra Ballast Pump w/1" Hose & 1/2" NPT Ports - 12V (60299)
Ultra Ballast Pump with 1" Hose & 1/2" NPT Ports - 12V

The Ultra Ballast Pump has been designed to pump water into ballast tanks. When reversed it will also pump water out of them.

Specifications:
  • Body: Bronze
  • Seal: Lip Seal, NBR Rubber
  • Impeller: MC 97 Rubber
  • O-Ring: NBR Rubber
  • Shaft: Stainless Steel
  • Bearings: Permanent lubricated, sealed, ball bearings
$192.98
68616XL.jpg
Jabsco - Jabsco Sliding Vane Self-Priming Diesel Transfer Pump - 9 GPM & 12V (68616)

Sliding Vane Self-Priming Diesel Transfer Pump - 9 GPM & 12V

Self-priming diesel transfer pump up to 35 liters/minute.

Features:

  • Connections: - for 19mm (¾”) bore hose.
  • Dimensions: - 180mm long, 110mm wide, 140mm high
  • Fuse Size: - 20(amp)
  • Output: - 35 litres/minute (7.7 gallons/minute) at 3m head. Maximum recommended total head 6m
  • Light duty, 40 minute rated diesel fuel transfer pump
  • Aluminium body, cast iron pump head
  • With integral fused switch and hose adapters
  • Unaffected by temperature extremes. Suitable for use from –30°C to +40°C
  • Self-priming up to 2.8m vertical lift
  • Use minimum 19mm (¾”) bore hose
  • Packaged Dimensions: L:23.00 x H:17.00 x W:21.00cm
  • Actual Weight: 2.62 Kg  (Approx. 3.12 kg packed)

WarningWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

$251.65
69000.gif
SHURFLO - SHURFLO Standard Flow Marine Ballast Pump - 12 GPM & 12 VDC - Bronze Housing (69000)

Standard Flow Marine Ballast Pump - 12 GPM & 12 VDC - Bronze Housing

The Shurflo Standard Ballast Pump was specially designed and developed for high capacity ballast tank applications in ski and wake boats, providing rapid fill and drain rates in a readily adaptable configuration, able to operate on a 25 Amp circuit. The high efficiency, high torque motor in combination with a high modulus neoprene compound impeller provide fast priming, long life, and consistent performance. Close internal tolerances help reduce leak back when the pump is mounted below the ballast tank. The Standard Ballast is built on the latest Shurflo motor series which includes fully sealed heavy die cast end bells, electro-coat finish throughout, and a steel mounting plate for reliable performance and durability in engine compartment conditions.

Features:

  • 2 VDC Sealed Corrosion Resistant Electro-Coated Motor
  • 14 AWG Lead Wires
  • Reversible Flexible Impeller
  • Bronze Pump Body
  • Self-Primes up to 4 feet vertically
  • Ports: ½” Internal Pipe Threads,
  • 1” External Hose Barb
  • Ignition Protected
  • CE and IMCI certification

Pump Design:

  • Type: Reversible Flexible Impeller
  • Ports: ½” Internal Pipe Threads, 1” External Hose Barb
  • Liquid: 200°F [93°C] Max
  • Prime: 4 Feet [1.2 M]
  • Run Dry: Not Recommended

Electrical:

  • Motor: 12V DC Permanent Magnet,
  • Intermittent Duty
  • Protection: Need External Fuse (not supplied)
  • Leads (Red): 14.5” [0.36M] Tinned 14 AWG
  • Leads (Black): 12.5” [0.31M] Tinned 14 AWG
  • Fuse: 25 Amp Fuse Recommended
  • Control: No Control – External Switch required

Materials:

  • Housings: Bronze
  • Impeller: Neoprene
  • Hardware: Brass/Stainless

Agency Approvals:

  • USCG Electrical Standards 183.410
  • ISO 8846 Marine for IGNITION PROTECTION on gasoline power vessels
  • CE and IMCI certification
$233.97
75319XL.jpg
GROCO - GROCO Heavy Duty Positive Displacement Touch Pad Reversing Vane Pump - 12V (75319)

Heavy Duty Positive Displacement Touch Pad Reversing Vane Pump - 12V 

GROCO  Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor, #316 stainless steel shaft, and touchpad (RT) control.

Specifications:

  • Self Priming: YES
  • Thread NPT: 1/2" + Garden Hose Adaptor
  • Control Type: Pump Mounted Touch Pad 
  • Max GPM: 6.5
  • Breaker DC: 30 Amp
$528.06
75321XL.jpg
GROCO - GROCO Commercial Duty Vane Pump - 12V (75321)

Commercial Duty Vane Pump - 12V

GROCO  Vane Pumps are self-priming. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor and #316 stainless steel shaft. SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI. 

Specifications:

  • Self Priming: YES
  • Thread NPT: 1/2" + Garden Hose Adaptor
  • Control Type: None
  • Max GPM: 7
  • Breaker DC: 30 Amp
Out of Stock
$704.34
75323XL.jpg
GROCO - GROCO Commercial Duty Reversing Vane Pump - 12V (75323)

Commercial Duty Reversing Vane Pump - 12V

GROCO  Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor, #316 stainless steel shaft, and reversing (R). SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI. 

Specifications:

  • Self Priming: YES
  • Thread NPT: 1/2" + Garden Hose Adaptor
  • Control Type: Pump Mounted Reversing Switch
  • Max GPM: 7
  • Breaker DC: 30 Amp
Out of Stock
$856.06
75325XL.jpg
GROCO - GROCO Commercial Duty Remote Reversing Vane Pump - 12V (75325)

Commercial Duty Remote Reversing Vane Pump - 12V 

GROCO  Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor, #316 stainless steel shaft, and  remote reversing (RR). SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI. 

Specifications:

  • Self Priming: YES
  • Thread NPT: 1/2" + Garden Hose Adaptor
  • Control Type: Remote Momentary Reversing Switch
  • Max GPM: 7
  • Breaker DC: 30 Amp